Category: Articles

Posted on by

Common failures of WD PCB 2060-701265-001

There are many reasons for the damage WD PCB 2060-701265-001, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of WD PCB 2060-701265-001

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged WD PCB 2060-701265-001

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 2060-701265-001 for WD 3.5″ IDE HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: WD PCB 2060-701265-001 firmware transfer

Posted on by

Common failures of WD PCB 2060-771822-002

There are many reasons for the damage WD PCB 2060-771822-002, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of WD PCB 2060-771822-002

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged WD PCB 2060-771822-002

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 2060-771822-002 for WD 3.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: WD PCB 2060-771822-002 firmware transfer

Posted on by

Common failures of Seagate PCB 100741095

There are many reasons for the damage Seagate PCB 100741095, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of Seagate PCB 100741095

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged Seagate PCB 100741095

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 100741095 for Seagate 2.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: Seagate PCB 100741095 firmware transfer

Posted on by

Common failures of Fujitsu PCB CA26350-B10304BA

There are many reasons for the damage Fujitsu PCB CA26350-B10304BA, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of Fujitsu PCB CA26350-B10304BA

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged Fujitsu PCB CA26350-B10304BA

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB CA26350-B10304BA for Fujitsu 2.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: Fujitsu PCB CA26350-B10304BA firmware transfer

Posted on by

Common failures of WD PCB 2060-800039-001

There are many reasons for the damage WD PCB 2060-800039-001, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of WD PCB 2060-800039-001

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged WD PCB 2060-800039-001

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 2060-800039-001 for WD 3.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: WD PCB 2060-800039-001 firmware transfer

Posted on by

Common failures of WD PCB 2060-771698-002

There are many reasons for the damage WD PCB 2060-771698-002, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of WD PCB 2060-771698-002

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged WD PCB 2060-771698-002

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 2060-771698-002 for WD 3.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: WD PCB 2060-771698-002 firmware transfer

Posted on by

Common failures of WD PCB 2060-701267-001

There are many reasons for the damage WD PCB 2060-701267-001, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of WD PCB 2060-701267-001

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged WD PCB 2060-701267-001

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 2060-701267-001 for WD 3.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: WD PCB 2060-701267-001 firmware transfer

Posted on by

Common failures of WD PCB 2060-800001-002

There are many reasons for the damage WD PCB 2060-800001-002, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of WD PCB 2060-800001-002

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged WD PCB 2060-800001-002

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 2060-800001-002 for WD 3.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: WD PCB 2060-800001-002 firmware transfer

Posted on by

Common failures of Seagate PCB 100656494

There are many reasons for the damage Seagate PCB 100656494, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of Seagate PCB 100656494

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged Seagate PCB 100656494

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB 100656494 for Seagate 3.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: Seagate PCB 100656494 firmware transfer

Posted on by

Common failures of Toshiba PCB G002587-0A

There are many reasons for the damage Toshiba PCB G002587-0A, the following is a summary of the common faults, by troubleshooting the following problems one by one, I hope you can find the cause of the PCB damage.

Common failures of Toshiba PCB G002587-0A

1. Circuit components are damaged

  • Capacitor failure: Capacitors may bulge and leak. This is mainly caused by prolonged use or high operating temperatures.
  • Resistor Damage: The resistor may burn out due to overcurrent. When there is an abnormal condition such as a short circuit in some components on the hard disk PCB, the current flowing through the resistor will exceed its rated value, causing the resistor to heat up excessively and be damaged.
  • Chip failure: The main control chip is one of the core components of the hard disk circuit board. It can be damaged by electrostatic discharge (ESD). In daily use, if proper electrostatic protection measures are not taken, for example, the static electricity generated by the human body in a dry environment may be conducted to the main control chip through finger contact, resulting in the breakdown of the internal circuit of the chip.

    The motor driver chip is also the part that is prone to problems. It is responsible for controlling the speed of the hard drive motor. If the motor driver chip is damaged, the motor may not start normally or the speed may be unstable, and the hard disk will not be recognized or the phenomenon of frequent jamming during the working process will occur.

2. The line problem

  • Short circuits: Circuits on hard drive boards can be short-circuited due to dust, moisture, or damaged components.
  • Line breaks: Line breaks are usually caused by line aging, long-term vibration, or physical damage.

3. Interface issues

  • Damaged Power Connector: The power connector may be damaged due to improper plugging and unplugging. For example, when plugging and unplugging a hard drive power cable, if you use too much force or the angle is off, the pins of the interface may be deformed or broken. In addition, the solder joints of the power connector may become loose due to long-term current shock or vibration, resulting in poor contact.
  • Data Interface Corruption: The pins of the data interface may be oxidized. This is mainly due to the influence of moisture or corrosive gases in the environment.

Fix damaged Toshiba PCB G002587-0A

After finding the cause of the damage to the PCB through the above steps, we can start to repair the PCB, like damaged components such as capacitors, resistors, chips, power interfaces, data interfaces, etc., we can replace them with components of the same specification, if we can’t find a suitable replacement component, we can also replace the entire PCB, the PCB G002587-0A for Toshiba 2.5″ SATA HDD can be purchased on our website, but please note that the BIOS chip also needs to be replaced with the original chip: Toshiba PCB G002587-0A firmware transfer